Modify the Linksys hardware

From Embedded Xinu
(Difference between revisions)
Jump to: navigation, search
(updating this page to explain using the new transceivers. not finished yet.)
Line 1: Line 1:
 
== Summary ==
 
== Summary ==
  
This will walk through adding hardware to a [http://www.linksys.com Linksys] [[WRT54GL]] wireless router that will take advantage of existing leads on the PCB for two UART connections, which will be exposed as DB9 connectors mounted to the faceplate of the router.  These connections can be used to communicate with the serial console for [[XINU]] and also to interact with the [[Common Firmware Environment]]'s command line interface.  Gaining direct access to [[CFE]] is a key step towards being able to run [[XINU]] on the router.
+
This will walk through adding hardware to a [http://www.linksys.com Linksys] [[WRT54GL]] wireless router that will take advantage of existing leads on the PCB for two UART connections, which will be exposed as DB9 serial port connectors mounted to the faceplate of the router.  These connections can be used to communicate with the serial console for [[XINU]] and also to interact with the [[Common Firmware Environment]]'s command line interface.  Gaining direct access to [[CFE]] is a key step towards being able to run [[XINU]] on the router.
  
 
== Before Starting ==
 
== Before Starting ==
Line 24: Line 24:
 
| $4.99
 
| $4.99
 
|-
 
|-
| 1
+
| 2
 
| IDC socket connector
 
| IDC socket connector
 
| 0.1”, 10 conductor  
 
| 0.1”, 10 conductor  
Line 30: Line 30:
 
| $0.25
 
| $0.25
 
|-
 
|-
| 1
+
| 2
| IDC shrouded header
+
| IDC shrouded double header
 
| 0.1”, 10 conductor
 
| 0.1”, 10 conductor
 
| Jameco 67811CM
 
| Jameco 67811CM
Line 37: Line 37:
 
|-
 
|-
 
| 1
 
| 1
| RS232 Transmitter/Receiver
+
| ADM202 Transceiver Chip
| IC 2DVR/2RCVR RS232 5V 20-DIP
+
| ?????????????
| DigiKey MAX233CPP-ND
+
| ?????????????
| $7.45
+
| $?.??
 +
|-
 +
| 2
 +
| Capacitor 220 nF
 +
| ?????????????
 +
| ?????????????
 +
| $?.??
 +
|-
 +
| 3
 +
| Capacitor 100 nF
 +
| ?????????????
 +
| ?????????????
 +
| $?.??
 +
|-
 +
| 1
 +
| Transceiver Board
 +
| ?????????????
 +
| ?????????????
 +
| $?.??
 
|-
 
|-
 
| 1
 
| 1
Line 76: Line 94:
  
 
[[Image:Wrt54gl-layout.jpg|thumb|250px|left|An overhead view to get your bearings. The serial header is (D) here.]]
 
[[Image:Wrt54gl-layout.jpg|thumb|250px|left|An overhead view to get your bearings. The serial header is (D) here.]]
Once the PCB has been removed from the case, locate the serial header holes provided by LinkSys.  This would be a grid of 10 holes (5x2) located on the bottom-right corner of the board when the antennae stubs are on top (see the top-down photo for clarification). [[Image:Serial.jpg|thumb|250px|right|A closer look at our attached serial header.]] These ten holes hold all of the input and output for the two serial interfaces--UART0, and UART1--on the device.
 
  
Now, we could just solder wires right onto these holes, but a by placing a nice 10-pin header on the board we can easily attach and detach a 10 connection cable.  This is where you will use your '''soldering iron''' to solder the '''IDC shrouded header''' onto the board.
+
Once the PCB has been removed from the case, locate the serial header holes provided by LinkSys. This would be a grid of 10 holes (5x2) located on the bottom-right corner of the board when the antennae stubs are on top (see the top-down photo for clarification). These ten holes hold all of the input and output for the two serial interfaces--UART0, and UART1--on the device.
 +
 
 +
[[Image:Serial.jpg|thumb|250px|right|A closer look at our attached serial header.]]
 +
 
 +
 
 +
Now, we could just solder wires right onto these holes, but a by placing a nice 10-pin header on the board we can easily attach and detach a 10 connection cable.  Here you will use your '''soldering iron''' to solder the '''IDC shrouded double header''' onto the board.
 +
 
 +
<h3 style="clear:both;"> Task Three: Create the ADM202 Transceiver Circuit Board </h3>
 +
 
 +
[[Image:Transceiver diagram.JPG|thumb|400px|left|Schematic showing the connections between the components of the ADM202 transceiver circuit board and between the board and the DB9 serial ports.]]
 +
[[Image:Transceiver board.jpg|thumb|150px|right|Blank transceiver board before adding components.]]
 +
[[Image:Soldered transceiver.jpg|thumb|150px|right|Transceiver board with all soldered components in place except ribbon cables.]]
 +
 
 +
The next step is to actually create the circuit board used to handle and bridge the input and output from the router and the two DB9 serial ports used to communicate between the backend router and frontend machine. Again, you'll need your '''soldering iron''' to secure the different pieces in the transceiver board.
 +
 
 +
Using the diagram on the left, solder the '''shrouded double header''', the '''socket''', and the '''capacitors''' into the board in the appropriate places. '''NOTE:''' the positions of the components on the physical board are not represented in the diagram, but the underside of the board shows the connections between each component.
 +
 
 +
The pictures to the right show the transceiver board in various stages of completion. The top one shows the blank board on which the other components will be added. The bottom one shows the '''shrouded double header''', the '''socket''', and the '''capcitors''' soldered in place. The next step is to insert the actual ADM202 chip into the socket. After that six wires from a chopped up piece of the ribbon cable (or any six spare wires) need to be soldered into place in the six holes (two sets of three) at the bottom of the transceiver board. The resulting completed transceiver board should look something like the picture below the diagram.
 +
 
 +
[[Image:Completed transceiver.jpg|thumb|400px|left|Complete transceiver board with all components in place.]]
 +
 
 +
 
 +
<h3 style="clear:both;"> Task Four: Attach Tranceiver Board to the Router</h3>
 +
 
 +
[[Image:Tranceiver attached.jpg|thumb|200px|left|Transceiver board attached via ribbon cable to the serial header soldered into the router's board.]]
 +
First take a piece of ribbon cable and attach each end to one of your IDC socket connectors. Then attach one connector to the header we soldered into the router's board and the other connector to the header we soldered into the transceiver board. The result should look something like the picture to the left.
 +
 
 +
<h3 style="clear:both;"> Task Five: Attach Transceiver Board to DB9 Serial Ports</h3>
 +
[[Image:Front sticker.jpg|thumb|100px|right]]
 +
[[Image:Front.jpg|thumb|100px|right]]
 +
[[Image:Modified front.jpg|thumb|100px|right]]
 +
Before soldering the wires from the transceiver board to the serial ports, it is a good idea to drill two holes in the front of the router's casing to use for the serial ports. The three pictures to the right show how to take off the front sticker and what the case should look like after you've drilled two holes in the front for the serial ports. It is also a good idea to cut the sticker and place the left part back on to cover up the holes in the casing.
  
This will be the only soldering required for the LinkSys PCB.  The rest of the work will be done wiring the MAX233A transceiver and the DB9 connectors correctly and then the finished product just has to be plugged it into this header.
 
  
 
=== Task Three: Wire Serial Header to MAX233A ===
 
=== Task Three: Wire Serial Header to MAX233A ===

Revision as of 03:00, 20 June 2008

Contents

Summary

This will walk through adding hardware to a Linksys WRT54GL wireless router that will take advantage of existing leads on the PCB for two UART connections, which will be exposed as DB9 serial port connectors mounted to the faceplate of the router. These connections can be used to communicate with the serial console for XINU and also to interact with the Common Firmware Environment's command line interface. Gaining direct access to CFE is a key step towards being able to run XINU on the router.

Before Starting

Parts List

Quantity Part Name Details Part / Model Number Price
1 LinkSys WRT54GL Router 802.11b/g wireless broadband router Linksys WRT54GL ~$65.00
1 Ribbon cable 28 AWG, 10 conductor, 25' Jameco 643508CM $4.99
2 IDC socket connector 0.1”, 10 conductor Jameco 32491CM $0.25
2 IDC shrouded double header 0.1”, 10 conductor Jameco 67811CM $0.33
1 ADM202 Transceiver Chip  ?????????????  ????????????? $?.??
2 Capacitor 220 nF  ?????????????  ????????????? $?.??
3 Capacitor 100 nF  ?????????????  ????????????? $?.??
1 Transceiver Board  ?????????????  ????????????? $?.??
1 DB9 Female 22AWG,SOLDER CUP Jameco 15771CM $0.59
1 DB9 Male 22AWG,SOLDER CUP Jameco 15747CM $0.59

(We provide this parts list as a data point; we offer no guarantees about current prices, and it is not our intent to endorse any particular vendor.)

Tools List

  • Soldering Iron
  • Dremel tool (for cutting holes in plastic case)
  • Multimeter, or some other way of checking for proper connections

Steps to Modify the Hardware

Task One: Open the Router

It's really very easy.

There are no screws or tools needed to open the router, just pop open the front with your thumbs as shown in the picture. Some nice illustrated opening instructions can be found for a more detailed explanation of this step

DO NOTE: This is where the warranty on the router is voided!

Task Two: Attach the Serial Header

An overhead view to get your bearings. The serial header is (D) here.

Once the PCB has been removed from the case, locate the serial header holes provided by LinkSys. This would be a grid of 10 holes (5x2) located on the bottom-right corner of the board when the antennae stubs are on top (see the top-down photo for clarification). These ten holes hold all of the input and output for the two serial interfaces--UART0, and UART1--on the device.

A closer look at our attached serial header.


Now, we could just solder wires right onto these holes, but a by placing a nice 10-pin header on the board we can easily attach and detach a 10 connection cable. Here you will use your soldering iron to solder the IDC shrouded double header onto the board.

Task Three: Create the ADM202 Transceiver Circuit Board

Schematic showing the connections between the components of the ADM202 transceiver circuit board and between the board and the DB9 serial ports.
Blank transceiver board before adding components.
Transceiver board with all soldered components in place except ribbon cables.

The next step is to actually create the circuit board used to handle and bridge the input and output from the router and the two DB9 serial ports used to communicate between the backend router and frontend machine. Again, you'll need your soldering iron to secure the different pieces in the transceiver board.

Using the diagram on the left, solder the shrouded double header, the socket, and the capacitors into the board in the appropriate places. NOTE: the positions of the components on the physical board are not represented in the diagram, but the underside of the board shows the connections between each component.

The pictures to the right show the transceiver board in various stages of completion. The top one shows the blank board on which the other components will be added. The bottom one shows the shrouded double header, the socket, and the capcitors soldered in place. The next step is to insert the actual ADM202 chip into the socket. After that six wires from a chopped up piece of the ribbon cable (or any six spare wires) need to be soldered into place in the six holes (two sets of three) at the bottom of the transceiver board. The resulting completed transceiver board should look something like the picture below the diagram.

Complete transceiver board with all components in place.


Task Four: Attach Tranceiver Board to the Router

Transceiver board attached via ribbon cable to the serial header soldered into the router's board.

First take a piece of ribbon cable and attach each end to one of your IDC socket connectors. Then attach one connector to the header we soldered into the router's board and the other connector to the header we soldered into the transceiver board. The result should look something like the picture to the left.

Task Five: Attach Transceiver Board to DB9 Serial Ports

Front sticker.jpg
Front.jpg
Modified front.jpg

Before soldering the wires from the transceiver board to the serial ports, it is a good idea to drill two holes in the front of the router's casing to use for the serial ports. The three pictures to the right show how to take off the front sticker and what the case should look like after you've drilled two holes in the front for the serial ports. It is also a good idea to cut the sticker and place the left part back on to cover up the holes in the casing.


Task Three: Wire Serial Header to MAX233A

Diagram showing connections from the MAX233A to the DB9 connectors and to the board. Note pins 4 and 6 on the board header.

Using information on the diagram, make the connections from the IDC shrouded header to the MAX233A RS232 Transmitter/Receiver chip using your soldering iron. As you can see from the photos, we did this with the ribbon cable from our parts list. The IDC socket connector goes on one end of the cable, and the correct connections are made to the RS232 Transmitter/Receiver on the other. Because we will be mounting our DB9 connectors to the front of the case, this will allow for easy disconnection and opening of the case. In terms of cable length, try and decide where you are going to mount the MAX233A on the outer case so you can estimate correctly.

Be sure to test all of your connections thoroughly before proceeding.

Task Four: Wire the DB9 Connectors to the MAX233A

The MAX233A wired to the ribbon cable and the DB9 connectors.

For the following connections, you are going to use the soldering iron and either chopped up portions of the ribbon cable or some other wire (which would probably be more convenient).

Checking the wiring diagram again, note that there are several loopback connections per DB9 connector in order to fake RS232 hardware flow control compliance. It would be a good idea to get these out of the way first. Then, make the connections required from the RS232 Transmitter/Receiver to the DB9 connectors, remembering to leave enough slack for where you plan on mounting the MAX233A and the connectors.

Again, before mounting anything, test that all connections correspond to the diagram.

Task Five: Mount DB9 Connectors to the Router Faceplate

This is the final version of the faceplate of our router, with the two external serial ports attached and ready to go.

Using your trusty dremel cut a few DB9 shaped holes in the plastic casing of the router. There are several options for placement; we chose the front so that multiple routers would still be stackable. The picture at right shows the placement of our connectors with wires attached. The fit is quite tight; you may wish to consider only installing one jack (you only need port 0 to communicate with the router, your plans may not call for using the second serial port) or installing them horizontally instead of vertically.

Using either epoxy or mounting screws (we used a combination of both, as one of our jacks could not fit a hole for a screw), secure the connectors to the case.

Following the theme, now would be a good time to do a final test on all connections, because next we are closing things up.

Task Six: Close the Router

This final task is best described in photos:

Now that everything is connected we can re-assemble it. First you put on the back/top half. Keyed ribbon cable is plugged in to serial port header on circuit board.
Next you can carefully install the front half (making sure not to break any of the wires we have).

Task Seven: Rejoice

Now you have a WRT54GL with two serial ports installed and ready to run your own operating system.

What to do next?

Connect UART0 to a computer and follow the next HOWTO on using a PC to connect to a modified router.

Personal tools
Namespaces

Variants
Actions
Navigation
Toolbox